OEM Hydraulic & Pneumatic Cylinders

Custom Cylinders International Inc. provides a wide variety of special designed hydraulic and pneumatic cylinders for the Original Equipment Manufacturing industry. The type of OEM developed or designed by Custom Cylinders International Inc. range from large hydraulic cylinders to operate press equipment to small pneumatic cylinders to lock prison doors. By providing new cylinders to the OEM customer, the natural associated service that has developed from the Production activity was a custom Repair Service. The ability to design special application hydraulic or air cylinders for specialized equipment, or provide low cost replacement cylinders for existing machinery has provided Custom Cylinders International Inc. with a wide range of experience in building unique cylinders.

 

RECREATIONAL VEHICLES

Custom Cylinders International Inc. has been manufacturing hydraulic cylinders for the Recreational Vehicle industry for more than 25 years. The majority of these cylinders fall into two types: Motor home leveling cylinders and Room slide out cylinders. In addition to the RV industry a large number of cylinders have been made for the horse trailer and general purpose trailer vehicles. A few of the brands known to use the Custom Cylinders International, Inc. design are Fleetwood Motor Homes, Fleetwood Travel Trailers, Kwikee Level Best Systems, Equalizer Systems, Dutchmen Travel Trailers, Sundowner Horse Trailers, Stetson Products, The Jack Systems, National RV, Gulf Stream Motor Homes, Hydra-Slide Products, Taylor-Newcomb Engineering, Coachmen Clipper, Viking Industries, and Sooner Trailers.

Replacement cylinders are maintained in stock for shipment to RV dealerships, RV internet stores, repair service companies, and directly to the consumer. In addition to providing the original replacement cylinders, CCI offers a rebuild and remanufacturing service for cylinders manufactured by other companies. Lead time for shipment will vary from stock cylinders shipment within 24 hours to less than 2 weeks for repair or remanufactured cylinders. Technical information is available through the Engineering department at CCI for specific applications.

In addition to the leveling and slide-out cylinders, CCI has developed a unique miniature hydraulic system for leveling fold down campers, using a standard hand held drill. From this application another system was developed to raise the roof on a fold down camper. This latter system is marketed under the brand names of ROOF JENIE and E-Z POWER LIFT SYSTEM. These systems can be installed by a dealer, the customer, or at our factory. Systems have been successfully installed on units manufactured by Coleman, Viking, Forest River, Dutchmen, and Starcraft

Pre-fabricated Cylinders

TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Living Room Red
141625-36H

TT / Living Room Red 1 5/8" Bore, 36 9/16" Stroke, 1 7/8" OD, 64 31/32" OAL, 5/8" Rod / The original design manufactured for any Fleetwood travel trailer that has the HYDRA-SLIDE hydraulic system that operates to move the Living Room, in or out, approximately 36 1/2". NOTE: This cylinder is typically used with 141500-36H when two cylinders are used to operate the room slide. To operate properly the cylinders must be of different bore size. The total length of the cylinder is measured from the center of the mounting hole at the rear, to the tip of the rod, and will be slightly less than 65". The outside diameter of the cylinder body is 1 7/8", while the rod diameter is 5/8". The color of the cylinder is to help identify the correct part number, and this cylinder color should be RED.

$197.34
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Living Room Black
141500-36H

TT / Living Room Black 1 1/2" Bore, 36 9/16" Stroke, 1 3/4" OD, 64 31/32" OAL, 5/8" Rod / The original design manufactured for any Fleetwood travel trailer that has the HYDRA-SLIDE hydraulic system that operates to move the Living Room, in or out, approximately 36 1/2". NOTE: This cylinder is typically used with 141625-36H when two cylinders are used to operate the room slide. To operate properly the cylinders must be of different bore size. The total length of the cylinder is measured from the center of the mounting hole at the rear, to the tip of the rod, and will be slightly less than 65". The outside diameter of the cylinder body is 1 3/4", while the rod diameter is 5/8". The color of the cylinder is to help identify the correct part number, and this cylinder color should be BLACK.

$187.19
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Bedroom Black
141500-24H

TT / Bedroom Black 1 1/2" Bore, 24" Stroke, 1 3/4" OD, 41"OAL, 5/8" Rod / The original design manufactured for any Fleetwood travel trailer that has the HYDRA-SLIDE hydraulic system that operates to move the Bed Room, in or out, approximately 24". The total length of the cylinder is measured from the center of the mounting hole at the rear, to the tip of the rod, and will be about 41". The outside diameter of the cylinder body is 1 3/4", while the rod diameter is 5/8". The color of the cylinder should be BLACK.

$174.00
TRAVEL TRAILER HYDRA-SLIDE CYLINDER-horse trailer travel trailer
162500-16HM

This rugged cylinder design is used for the single hitch leg of the combination horse trailer / travel trailer RV units. This design has been used for several years by the Sooner Trailer Manufacturing Company of Oklahoma. This cylinder is 2 1/2" bore X 16" and 3" X 18" stroke design with a 3/4" inside diameter cross tube on the cap (blind end) and a 3/4" cross hole drilled through the piston rod end. The rear port is a #6 SAE O ring boss and the front port is a #4 SAE O ring boss style. This basic design has been in production since 1999, with approximately 5,000 shipped from stock.

$124.70
TRAVEL TRAILER HYDRA-SLIDE CYLINDER horse trailer travel trailer
163000-16H

This rugged cylinder design is used for the single hitch leg of the combination horse trailer / travel trailer RV units. This design has been used for several years by the Sooner Trailer Manufacturing Company of Oklahoma. This cylinder is 2 1/2" bore X 16" and 3" X 18" stroke design with a 3/4" inside diameter cross tube on the cap (blind end) and a 3/4" cross hole drilled through the piston rod end. The rear port is a #6 SAE O ring boss and the front port is a #4 SAE O ring boss style. This basic design has been in production since 1999, with approximately 5,000 shipped from stock.

$126.32
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-12H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$126.36
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-18H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$132.23
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-20H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$128.00
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-25H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE ring boss ports, A ¾" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18" bolt or all-thread.

$130.00
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-30H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, A 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$136.80
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-36H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$153.02
TRAVEL TRAILER HYDRA-SLIDE CYLINDER FLEETWOOD DESIGN
141625-33H

TT / Living Room Blue 1 5/8" Bore, 33 9/16" Stroke, 1 7/8" OD, 64 31/32" OAL, 5/8" Rod / The original design for any Fleetwood travel trailer that has the HYDRA-SLIDE hydraulic system that operates to move the Living Room, in or out, approximately 33 1/2". NOTE: This cylinder is typically used with 141500-33H when two cylinders are used to operate the room slide. To operate properly the cylinders must be of different bore size. The total length of the cylinder is measured from the center of the mounting hole at the rear, to the tip of the rod, and will be slightly less than 65". The outside diameter of the cylinder body is 1 7/8", while the rod diameter is 5/8". The color of the cylinder is to help identify the correct part number, and this cylinder color should be BLUE.

$187.19
TRAVEL TRAILER HYDRA-SLIDE CYLINDER FLEETWOOD DESIGN
141500-33H

TT / Living Room Gray 1 1/2" Bore, 33 9/16" Stroke, 1 3/4" OD, 64 31/32" OAL, 5/8" Rod / The original design for any Fleetwood travel trailer that has the HYDRA-SLIDE hydraulic system that operates to move the Living Room, in or out, approximately 33 1/2". NOTE: This cylinder is typically used with 141625-33H when two cylinders are used to operate the room slide. To operate properly the cylinders must be of different bore size. The total length of the cylinder is measured from the center of the mounting hole at the rear, to the tip of the rod, and will be slightly less than 65". The outside diameter of the cylinder body is 1 3/4", while the rod diameter is 5/8". The color of the cylinder is to help identify the correct part number, and this cylinder color should be GREY.

$181.25
STROKE CONROL NUT FOR 141625-14H FRONT ROOM SLIDE CYLINDER
STROKE CONROL NUT FOR 141625-14H FRONT ROOM SLIDE CYLINDER
14SCN58-18-14H

PART# 14SCN58-18-14H MOTOR HOME BLACK Stroke control nut for the 14162500-14H hydraulic cylinder. This cylinder was used for the Flair, Pace Arrow, Bounder, American Eagle, and other Fleetwood Industries motor home brands to operate the front room slide. Due to the design of the slide out mechanism, this cylinder will usually fail due to lack of lubrication of the slide. In cooperation with the Fleetwood Motor Home engineering department a new design was developed that has proven to be quite successful in reducing the reasons for failure. VERSION #8 is now offered in the new configuration as a standard replacement item. The outside diameter of the cylinder body is 1 7/8", has a 3/4" rod, 14" stroke, and is approximately 21 3/4" from the center of the mounting hole to the tip of the rod. The color of the cylinder will be BLACK; however there were a number of cylinders painted different colors during the change over to the new version. Picture shows just the nut that stops the control nut, so the order will have the nut shown and a black stroke control nut. 

$29.85
SINGLE HITCH LEG HORSE AND TRAVEL TRAILER HYDRA-SLIDE CYLINDER
162500-16H

This rugged cylinder design is used for the single hitch leg of the combination horse trailer / travel trailer RV units. This design has been used for several years by the Sooner Trailer Manufacturing Company of Oklahoma. These two cylinders are 2 1/2" bore X 16" and 3" X 18" stroke design with a 3/4" inside diameter cross tube on the cap (blind end) and a 3/4" cross hole drilled through the piston rod end. The rear port is a #6 SAE O ring boss and the front port is a #4 SAE O ring boss style. This basic design has been in production since 1999, with approximately 5,000 shipped from stock.

$124.70
TRAVEL TAILER HYDRA-SLIDE MOTOR HOME LEVELING CYLINDER
182500-16HM

This cylinders design was originally designed in 1989 for the leveling systems used on RV motor homes. Companies that have used this cylinders design include Hughes Leveling Systems, Stetson Products, Kwikee Products, Equalizer Systems, The Jack Company, and other non-RV companies. Bore sizes are 2 1/2" and 3", non-repairable, feature heavy duty seals, heavy chrome plate on the piston rod, and stroke lengths from 8" to 30". This design has a heavy duty 16 hole mounting plate that is welded to the cylinder. The rod assembly does not allow any rotation in the operating cycle, and the rod end has a 3/4-10 threaded hole or a simple cross hole in the end for mounting a landing pad. Known RV motor homes that have used this design are National, Gulf Stream, Fleetwood, and Winnebago.

$167.61
RV MOTOR HOME LEVELING CYLINDER
163000-08H

No longer in Stock. Rebuild price is offered for this non repairable hydraulic cylinder. Parts and labor extra if more is needed to be done other than the basic rebuild. This hydraulic cylinder design was originally designed in 1989 for the leveling systems used on RV motor homes. Companies that have used this cylinders design include Hughes Leveling Systems, Stetson Products, Kwikee Products, Equalizer Systems, The Jack Company, and other non-RV companies. Bore sizes are 2 1/2" and 3", non-repairable, feature heavy duty seals, heavy chrome plate on the piston rod, and stroke lengths from 8" to 30". This design has a heavy duty 16 hole mounting plate that is welded to the cylinder. The rod assembly does not allow any rotation in the operating cycle, and the rod end has a 3/4-10 threaded hole or a simple cross hole in the end for mounting a landing pad. Known RV motor homes that have used this design are National, Gulf Stream, Fleetwood, and Winnebago.

$399.40
TRAVEL TRAILER HYDRA-SLIDE MOTOR HOME LEVELING CYLINDER
163000-10H

This cylinders design was originally designed in 1989 for the leveling systems used on RV motor homes. Companies that have used this cylinders design include Hughes Leveling Systems, Stetson Products, Kwikee Products, Equalizer Systems, The Jack Company, and other non-RV companies. Bore sizes are 2 1/2" and 3", non-repairable, feature heavy duty seals, heavy chrome plate on the piston rod, and stroke lengths from 8" to 30". This design has a heavy duty 16 hole mounting plate that is welded to the cylinder. The rod assembly does not allow any rotation in the operating cycle, and the rod end has a 3/4-10 threaded hole or a simple cross hole in the end for mounting a landing pad. Known RV motor homes that have used this design are National, Gulf Stream, Fleetwood, and Winnebago.

$189.00
TRAVEL TRAILER HYDRA-SLIDE CYLINDER - Equalizer Systems
201125-15H

Although this design was developed and used by several RV OEMs, this design group of hydraulic cylinders was developed for the EQUALIZER SYSTEMS COMPANY for use in recreational vehicles that used light duty room slide-out systems. This design group comes in stroke lengths of 12", 15", 18 1/2", 20", 25", 30", and 36", all based on a bore size of 1 1/8". The basic design is non-repairable, has #6 SAE O ring boss ports, 3/4" piston rod, 5/8-18 threaded rod end, and the rear cap is threaded for a 5/8-18 bolt or all-thread.

$126.36
Replacement Cylinder for a Woods Bat Wing Mower Hydraulic Cylinder
Woods Bat Wing Mower Hydraulic Cylinder
292500-11H

Replacement Hydraulic Cylinders for a Woods Bat Wing Mower Cylinder / 2 1/2" Bore, 1" Rod, 11 3/4" Stroke, Repairable Hydraulic Cylinder, 1" Pins, Pin to Pin Dimension 19 3/16" (Other stroke and sizes available) contact customer service. Send in the old hydraulic cylinder as a core charge of $50 and save 800.779.5544 

$250.00
CUB CADET HYDRAULIC LIFT CYLINDER
MTD Lawn Tractor
717-3005

Cub Cadet Hydraulic Lift Cylinder

CUB CADET PART #717-3005      

This is a discontinued deck lift cylinder for Cub Cadet Tractors, and is available from stock. Contact us for this and several other cylinders for Fleetwood Motor Homes, MTD Products, Cub Cadet Lawn, Fleetwood Travel Trailers, Sooner Horse Trailers, Dutchmen, Travel Trailers, Winnebago Motor Homes, National Motor Homes, Gulf Stream, and other horse trailer and recreational vehicle brands.

Discontinued hydraulic cylinders that are no longer available from Cub Cadet, MTD Products, and Hydra-Slide hydraulic systems, National Recreational Vehicles, Winnebago Motor Homes, Gulf Stream Motor Homes, Dutchmen Travel Trailers, and Sundowner Horse Trailers.

This part number was used on the Cub Cadet Yard tractor for hydraulically raising and lowering the mowing deck. Designed in 1983 and used for this purpose until approximately 1988, at which time it was replaced by several new designs in production up to 2001. Should fit 1800 series Garden Tractors and these 1864, 1863, 1841, 1811, 1812, 1712, 782, 782D. It is a repairable 2 ½” hydraulic cylinder, ¾” rod, double acting, cast steel cap, 2 3/8” stroke, ½” cross tube on the rod end, ½” cross hole on the cap end, with a maximum operating pressure of 800 PSI. This cylinder is available for use in many other applications where a short stroke, 1,000# force is required.

$80.00
MTD CUB CADET HYDRAULIC CYLINDER
MTD Cub Cadet Hydraulic Cylinder
717-3518

MTD Cub Cadet

Hydraulic Cylinder Part # 717-3518 similar to 717-3423 Disign 2000 Lift Cylinder

1 1/2" Bore, 1/2" Rod, 2.35" Stroke, 1000psi WP, 1/2" Rear pin hole, 5/8" X 1 1/2" slot in flange.

$276.42
MTD CUB CADET HYDRAULIC POWER STEERING CYLINDER
CTP part # 02003368
717-3502

MTD CUB CADET POWER STEERING CYLINDER

Part# 717-3502 For 6000 Series Tractor Power Steering Cylinder. Now with lube bearings each end, original design 1998.

9/16 - 18 SAE # 6 ORB PORTS 12 1/2" pin to pin installed length. 1 1/2" Bore, 1/2" rod, 6" Stroke, 3/4" Pin hole each end 1500 psi operating pressure, double acting. And 2003 MTD # 717-04119, 1 1/2" Bore, 1/2" Rod, 6 3/8" Stroke, 3/4" Pin hole each end 1500 psi operating pressure, double acting. And 261500-06H 12 1/2" installed #6 SAE 6" Stroke, CTP # 02003368 Designed 2007 1 1/2" Bore, 1/2" Rod, 4 1/2" Stroke, 7/8" Pin hole each end 1500 psi operating pressure, double acting.

$368.00
Cub Cadet MTD Power Steering Cylinder
Cub Cadet Power Steering Cylinder
717-3424 or 717-3041A

Cub Cadet MTD Power Steering Cylinder

Part# 717-3424 (1997) metric or 717-3041A (1985) 1/2 - 20 Threads over all length 12 3/8"

Power steering cylinder 1 1/2" Bore, 1/2" Rod, M12 threads for each end, 4" Stroke, 1000 psi operating pressure, over all length 13 3/4" double acting hydraulic cylinder.

$272.00
Cub Cadet MTD Lift Cylinder
Cub Cadet 5000 Series Lift Cylinder
717-3532

Hydraulic Cylinder Cub Cadet MTD Lift Cylinder

Part# 717-3532 (2002) original design 10" pin to pin installed length #6 O ring bose port, #4 changed in newer design. 2 3/8" Bore, 2 1/4" Rod, 5 1/2" Stroke, 3/4" Pin Holes, #4 SAE Ports, single acting, 5000 series lift cylinder, 2000 psi operating pressure.

$358.00
MTD CUB CADET FRONT HITCH LIFT HYDRAULIC CYLINDER
Cub Cadet Front Hitch Lift Cylinder
717-3456

Cub Cadet MTD Front Hitch Lift Cylinder

Part# 717-3456 original design 1998, Over all length 8 5/32" pin to pin installed length. 2" Bore, 5/8" Rod, 3" Stroke, 1/2" Pin Holes, #6 SAE Ports, Double acting, 1200 psi operating pressure.

$235.00
Actuant RV Company Motor Home storage tray cylinder
Power Gear Tray Cylinder
311000-12H

Motor Home storage tray cylinder by Actuant RV Company

The original product was developed by Kwikee Manufacturing Company for their slide out storage trays, typically located below the main body of the motor home or 5th wheel camper. It is hydraulic oil operated, and has a 12" stroke, double acting design, chrome rod diameter 9/16", Tube 1 1/4", Double ended design is mounted on 14 9/16" fixed points on cylinder body to RV. Over all length is 29 3/4" from end of chrome rod to opposite end of chrome rod. 1/8 - NPT hydraulic oil ports QTY 2, Clevis for each end not furnished use originals from old cylinder, operating pressure is 800 psi. Actuant Cylinder Part # 130-1275

Call for Repair price 1.800.779.5544

$900.00
MOTOR HOME FRONT ROOM HYDRAULIC SLIDE OUT CYLINDER
Motor Home hydraulic Room Cylinder
141625-14H

PART# 141625-14H MOTOR HOME RED OR BLACK 1 5/8" Bore, 14" Stroke, 1 7/8" OD , 21 23/32" OAL, 3/4" Rod / This cylinder was used for the Flair, Pace Arrow, Bounder, American Eagle, and other Fleetwood Industries motor home brands to operate the front room slide out. Due to the design of the slide out mechanism, this cylinder will usually fail due to lack of lubrication of the slide. In cooperation with the Fleetwood Motor Home engineering department a new design was developed that has proven to be quite successful in reducing the reasons for failure. VERSION #8 is now offered in the new configuration as a standard replacement item. The outside diameter of the cylinder body is 1 7/8", has a ¾" rod, 14" stroke, and is approximately 21 ¾" from the center of the mounting hole to the tip of the rod. The color of the cylinder will be BLACK; however there were a number of cylinders painted different colors during the change over to the new version.

$455.00